Edge flashing
New drip edge is tucked under the shingles over the gutter which stops the rot from coming back.
Exterior Services
Fascia Repair Mountainside, NJ
A roofer in Mountainside can repair or replace rotted fascia boards, reattach sagging gutters and fix the drip edge that keeps water off the wood, once the source of the water is found. Dial (908) 728-6030 to talk with a local roofer about the fascia.
The fascia sits right where water leaves the roof, so it is the first trim board to rot when that water goes the wrong way. Without a drip edge lapped into the gutter, runoff clings to the roof edge and wets the top of the fascia every storm. Over a few seasons the wood softens, the gutter screws lose their grip and the gutter starts to sag or pull away.
What starts as a soft board can spread well past the trim. Behind the board are the rafter tails, the roof decking at the edge and the soffit, and water that gets past the fascia soaks into all of them. On homes with metal fascia wrap, the rot often goes unseen until the gutter falls.
Before the visit, take a look along the roof edge from the ground. Note where paint is peeling, where gutters sag or have pulled away, and whether water pours over the gutter in heavy rain. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
Fascia Repair is often paired with soffit repair and gutter installation, depending on the cause.
Dealing with this in Mountainside, NJ right now? Call (908) 728-6030 and describe the problem to a roofer who works in Mountainside.
Call nowThe process
The fascia repair process
Here is how a roofer typically handles a fascia repair.
Find the water path
The visit starts with where the water comes from, usually a missing drip edge, a clogged gutter or a gutter with the wrong slope. Probing along the board shows where the rot starts and stops.
Take down the gutter
Gutters are taken down along the damaged stretch, which also shows how well the hangers were holding. This is a good time to check the gutter itself for leaks and bad seams.
Check the rafter tails
The roofer looks at the rafter ends and the sub-fascia, since soft framing will not hold a new board. Skipping it is the most common reason fascia fails twice.
Fit the board
New fascia in primed wood, PVC or composite is cut to fit, with scarf joints at the seams. End grain is sealed so it does not soak up water.
Close the gap
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. Without it, the same board will rot again.
Finish the edge
Gutters are rehung on the new fascia with a slight slope toward the outlets. Wood fascia gets a finish coat of paint.
What is included
What fascia repair covers
Rotted board repair
Damaged fascia is replaced with primed wood or PVC with sealed joints and ends.
Aluminum wrap
Metal wrap can be added over new or sound fascia to cut down on painting.
Gutter rehanging
Sagging gutters are rehung on solid fascia with new hangers with screws instead of loose spikes.
Rafter tail repair
Rotted rafter ends behind the fascia are sistered or rebuilt before the fascia goes back on.
Related service
Fascia Board Replacement Mountainside, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. It is also the moment to choose a material, whether primed wood, PVC, composite or wood with an aluminum wrap.
Timing fascia replacement with a reroof in Mountainside lets the new drip edge and the new boards go on together. Ask whether the roofer plans to remove the old boards or wrap over them, because wrapping soft wood only hides the rot. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Mountainside, NJ
Fascia board repair handles damage that is limited to a few spots, such as a rotted corner, the area under a leaky gutter seam or a section by a downspout. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. For a shallow soft spot, an epoxy consolidant and filler can restore the surface without cutting the board.
The repair is only worth doing if the water source is fixed at the same time. The cause is often a leaking gutter corner or a downspout that backs up. Sealed and painted, the patch holds up like the original wood.
Local help
Fascia Repair Near Me
In Mountainside, fascia tends to fail first on the sides of the house where gutters clog fastest. Across Mountainside and nearby communities including Westfield, Summit, New Providence and Garwood, the fascia under trees and heavy gutter loads is the first to go, and replacing a short section early is far easier than rebuilding the roof edge later.
Need fascia repair around Mountainside? Call (908) 728-6030 for a Mountainside roofer who serves the towns around it too.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Mountainside, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Smaller repairs
Small roof problems caught early usually stay small repairs.
Roofers who know Mountainside
Roofers in Mountainside know the roof types and weather wear common in local homes.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Fascia Repair questions
Do I need new fascia boards or just a repair?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. If the damage is widespread, new boards end up being the simpler fix. The roofer will probe the wood to see which option fits.
Why is my fascia rotting?
Water getting behind the gutter is the main cause. Overflowing gutters, gutters pitched the wrong way and roof edges without drip edge soak the board repeatedly. Peeling paint and unsealed cut ends speed up the damage.
Do fascia boards affect my gutters?
A gutter is only as secure as the board behind it. As rot sets in, fasteners loosen and the gutter starts to droop under the weight of water and debris. The fix is solid wood plus new hangers, pitched toward the downspout.
Is it safe to wrap rotted fascia in aluminum?
Metal wrap only belongs over sound wood. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Wrap is a good finish over new or solid fascia.
Which fascia material lasts longest?
Rot-proof materials such as PVC and composite last longest. Wood looks traditional and is easy to work with, though it needs upkeep. Whatever you choose, a proper drip edge and working gutters matter more than the board itself.
More questions? Call (908) 728-6030
Other services that may help
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, before rot spreads into the fascia and rafter tails.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Gutter repair for leaking seams, sagging runs, loose hangers and broken downspouts, so roof water drains where it should again.
Learn moreRoof Repair
Targeted roof repairs for wind, age and water damage, without replacing a roof that still has life left.
Learn more
Looking for something else?
See all roofing servicesTalk to a Mountainside roofer about fascia repair
Call now for Mountainside fascia repair and help in the towns around it.